Contact BSSA

Category: Martensitic & PPN Hardening Grades

Page 1 of 2

  1. 1
  2. 2
  1. Ambient temperature mechanical properties for BS EN 10297-2 for stainless steel seamless tubes for general purposes

    BS EN 10297-2 is the EN standard for seamles stainless steel tubes for general purposes. This article summarises the mechanical properties

  2. Ambient temperature mechanical properties of cold worked wire to EN 10088-3

    EN 10088-3 is the European Standard for stainless steel long products. It includes a provision for wire in the cold worked condition. Although this is not strictly for spring wire (which is EN 10270-3), the properties shown in Table 18 are such that springs could be made from material in this condition

  3. Ambient temperature mechanical properties of martensitic and precipitation hardening stainless steel bright bars to BS EN 10088-3

    The BS EN 10088-3 standard gives the mechanical properties for stainless steel semi-finished products, bars, rods and sections for general purposes. The properties given in this article are proof strength, tensile strength, elongation and hardness of martensitic and precipitation hardening stainless steels.

  4. Ambient temperature mechanical properties of martensitic and precipitation hardening stainless steel long products to BS EN 10088-3

    The BS EN 10088-3 standard gives the mechanical properties for martensitic and precipitation hardening stainless steel semi-finished products, bars, rods and sections for general purposes. The properties given are proof strength, tensile strength, elongation and hardness.

  5. Ambient temperature mechanical properties of martensitic stainless steel flat products to BS EN 10088-2

    The BS EN 10088-2 is the material standard for stainless steel sheet, plate and strip for general purposes. The current edition was published in October 2014. Mechanical properties are specified, including proof and tensile strength, elongation, impact strength and hardness. Only tensile and hardness properties are tabulated in this article for the martensitic grades. LAST UPDATED 25th NOVEMBER 2014.

  6. Ambient temperature mechanical properties of precipitation hardening stainless steel flat products to BS EN 10088-2

    The BS EN 10088-2 is the material standard for stainless steel sheet, plate and strip for general purposes. The current edition was published in October 2014. Mechanical properties are specified include proof strength, tensile strength and elongation. These are tabulated in this article for the precipitation hardening grades 1.4542 and 1.4568. LAST UPDATED 25th NOVEMBER 2014.

  7. Ambient temperature physical properties of stainless steels to BS EN 10088-1

    Ambient temperature physical properties, including density, modulus of elasticity (Young's modulus), coefficient of thermal expansion, thermal conductivity, specific heat (heat content or heat capacity) and electrical resistivity for a range of ferritic, martensitic, austenitic and duplex stainless steel types are tabulated. Some explanation of the units used for these properties is given.

  8. Chemical composition of stainless steel castings to BS EN 10283

    BS EN 10283 is the material standard for stainless steel castings for corrosion resisting purposes. The chemical composition of stainless steel grades covered in the this standard include 1.4011 1.4008 1.4317 1.4405 1.4411 1.4525 1.4309 1.4308 1.4552 1.4409 1.4408 1.4581 1.4412 1.4446 1.4458 1.4527 1.4584 1.4416 1.4587 1.4588 1.4593 1.4347 1.4470 1.4468 1.4517 1.4417 and 1.4469.

  9. Chemical composition of stainless steel flat products for pressure purposes to BS EN 10028-7

    BS EN 10028-7 is the material standard for stainless steel sheet, plate and strip for pressure purposes. The current edition was published in December 2007. The grades are mostly a subset of the grades covered in BS EN 10088-2 for general purposes. There are also a number of creep resisting steels from BS EN 10302.  The chemical composition of stainless steel grades covered in the this standard are:

    Ferritic 1.4003 1.4516 1.4520 1.4510 1.4513 1.4521 1.4526 1.4509 

    Martensitic 1.4313 1.4418

    Austenitic 1.4318 1.4307 1.4306 1.4315 1.4311 1.4301 1.4541 1.4550 1.4335 1.4404 1.4406 1.4401 1.4466 1.4571 1.4580 1.4432 1.4429 1.4436 1.4435 1.4434 1.4438 1.4439 1.4563 1.4539 1.4537 1.4547  1.4529

    Duplex 1.4362 1.4462 1.4507 1.4410 1.4501

    Creep Resisting 1.4910 1.4941 1.4948 1.4950 1.4951 1.4958 1.4959 1.4961

  10. Chemical compositions of stainless steels to EN 10216-5

    BS EN 10216-5 2004 is the European standard: Seamless stainless steel tubes for pressure purposes- Technical delivery conditions. It contains austenitic, duplex, creep resisting stainless steels. There are no ferritic, martensitic or heat resisting steels.

Page 1 of 2

  1. 1
  2. 2

top

Office and Postal Address: BSSA, Regus, Blades Enterprise Centre, John Street, Sheffield S2 4SW

Registered Office: Pegasus House, 463A Glossop Road, Sheffield S10 2QD

Tel: +44 (0)114 292 2636    |     Email: admin@bssa.org.uk

Copyright © 2017 British Stainless Steel Association

web design sheffield by Llama Digital