Contact BSSA

Category: Standards, Specifications & Grades

Page 13 of 14

  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  6. 6
  7. 7
  8. 8
  9. 9
  10. 10
  11. 11
  12. 12
  13. 13
  14. 14
  1. Tolerances to BS EN 10059 for hot rolled square stainless steel bars

    Size, corner radius, straightness, twist and 'out-of-squareness' tolerances for square bars are tabulated along with notes on measurement methods.

  2. Tolerances to BS EN 10060 for hot rolled round stainless steel bars

    Diameter, ovality and straightness tolerances for round bars are tabulated along with notes on measurement methods.

  3. Tolerances to BS EN 10061 for hot rolled hexagon stainless steel bars

    Size (width across flats), corner radius, straightness, twist and 'out-of-section' tolerances for hexagon bars are tabulated along with notes on measurement methods.

  4. Tolerances to BS EN 10258 for cold rolled narrow stainless steel strip

    Specific features of the European dimensional tolerance for cold rolled narrow stainless steel strip are described. The tolerences covered are thickness, width, length, flatness and edge waviness, out-of-squareness and edge camber.

  5. Tolerances to BS EN 10259 for cold rolled wide stainless steel strip

    Specific features of the European dimensional tolerance for cold rolled wide stainless steel strip are described. The tolerences covered are thickness, width, length, flatness and edge waviness, out-of-squareness and edge camber.

  6. Tolerances to BS EN 10278 for bright stainless steel bars

    Tolerances for bright drawn, ground, turned and polished stainless steel bars are shown to BS EN 10278, derived from tolerance classes to ISO 286-2. The shapes covered include round, hexagon, square and flat bar sections and include. Cross section (diameter, width, thickness, across flats), ovality, length and straightness tolerances are tabulated.

  7. Tolerances to BS EN 10296-2 for welded stainless steel tube

    In addition to chemical composition and mechanical properties, BS EN 10296-2 also gives tolerances for straightness, outside diameter, wall thickness, length, height of weld seam,

  8. Tolerances to BS EN 10297-2 for seamless stainless steel tubes

    In addition to chemical composition and mechanical properties, BS EN 10297-2 also gives tolerances for straightness, outside diameter, wall thickness and length

  9. Tolerances to EN 10029 for hot rolled plate 3mm and above

    A summary of tolerances for hot rolled plate, also known as quarto plate, i.e. rolled as flat plate on a reversing mill. Not applicable to plate cut from coil also known as CPP continuously produced plate. Covers thickness, width, length, flatness, out-of-squareness and edge camber.

  10. Tolerances to EN 10051 for continuously rolled hot rolled plate sheet and strip

    The EN standard applicable to continuously hot rolled plate sheet and strip, also known as CPP. Covers tolerances on thickness, width, length, flatness, out of squareness, edge camber and crown. It has been superseded by ISO 9444

Page 13 of 14

  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  6. 6
  7. 7
  8. 8
  9. 9
  10. 10
  11. 11
  12. 12
  13. 13
  14. 14

top

Office and Postal Address: BSSA, Regus, Blades Enterprise Centre, John Street, Sheffield S2 4SW

Registered Office: Pegasus House, 463A Glossop Road, Sheffield S10 2QD

Tel: +44 (0)114 292 2636    |     Email: admin@bssa.org.uk

Copyright © 2017 British Stainless Steel Association

web design sheffield by Llama Digital